0 votes
by (160 points)

diamond grinding toolWhen grinding, an abrasive material comparable to carborundum is used to remove materials from the workpiece. When turning, material is removed from the workpiece with a chopping tool. The worpiece is often clamped in the jaws of a chuck, and the chuck turns. the instrument is clamped to a toolpost and moved along the workpiece and into the workpiece so as to chop materials off in a measured quantity.


What's difference between trituration and levigation?
levigation is wet grinding whereas trituration is dry grinding


What's difference between turning machine and lathe machine?
There isn't a difference between a turning machine and a lathe. They are two names for the same kind of machine


Why the facility required in grinding process is greater than turning?
Turning makes use of a knife edge to shear a piece off grinding makes use of a stone cutting machine for sale; Sheenahass 468170 Xtgem wrote, to abrade and break off a pieces the width of the stone turning point or line contact grinding area contact


What would trigger a grinding noise when turning the steering wheel to the best in a ford transit?
most grinding noises that come from turning is normally a cv axle that needs to be changed. Can be a bad wheel bearing. If you hear the grinding when turning to the correct then the left front wheel bearing is dangerous.


What's the difference between twisting and turning?
different between twist and switch


What is the distinction between mixing and grinding?
Grinding is like chopping into tiny pieces. For example, humans "grind" the food they chew before swallowing, and the mastication (grinding) is part of the digestive process. Blending is mixing to a clean mixture.


What is the distinction between pounding grain and grinding grain?
they are the same they are simply used in different kind of sentences.


What is the differences between milling and turning?
Fundamental difference between turning and milling is that , In turning the device is fastened and the job rotates whereas in milling the job is fastened and the instrument rotates


What makes a grinding noise when turning the steering wheel?
A defective CV joint will make a grinding noise when you turn the steering will. A nasty strut also can trigger a grinding noise.


Have 02 Saturn SL 2 26000 mi grinding noise when turning proper or left has new brakes tie rods steering rack all vendor changed this week nonetheless makes grinding sound when turning right left?
Unhealthy wheel bearings usually cause a grinding noise, and are identified to solely cause it when turning.


What may trigger a popping - grinding noise when turning a Windstar?
Potential causes of popping/grinding noises when turning: Wheel bearings CV joint / axle Brakes See "Associated Questions" beneath for more


What sound would a defective wheel bearing make?
scraping sweeking grinding clicking seems like one thing is grinding might be most apparent when turning


What is the distinction between Canine teeth and molar teeth?
Canine teeth are sharp and used for tearing, molars are flat and used for grinding.


What makes grinding noise when turning?
not sure sound like it comes from front suspension


The difference between turning and cranking an engine?
usually , cranking an engine is completed with igniton the place turning is completed by hand with the ignition off so because it will not begin


What's the distinction between turning off and restart?
Turning off it stays off until you turn it on, restart just automaticlly turns off then again on.


What's the difference between nutrition and respiration?
Nutrition is getting food, respiration is turning the food into energy


What was the function of a medieval miller?
The miller oversaw the grinding of the corn during the means of turning it into flower.


What causes a grinding sound when turning and a whining sound when accelerating?
presumably your wheel bearing is on its approach out


What causes Proper entrance tire space to make deep grinding sound making an extreme righ turn?
Have your brakes checked, rust or wear on brakes may cause grinding when turning.


What causes a grinding noise while turning at sluggish speeds?
I'd strive changing tires, worked for me.


When driving grinding sound goes away when turning to the best?
Bad right entrance wheel bearing.


What causes a low grinding sound close to the Alternator when turning the Van off?
The bearings on the alternator could be going dangerous. Take away the belt from the alternator then spin the alternator by hand to pay attention for grinding.


What's grinding crunchin sound when turning my mercury marquis in either direction?
Should you automobile is entrance-wheel drive, greater than likely, that grinding crunching sound while you flip is coming from the CV joints.


Grinding noise when turning the steering wheel in a 2003 Mitsubishi eclipse?
many reasons, steering pump, cv joints could also be going out, otherwise you might be grinding some plastic that goes across the wheel


What is the distinction between turbine turning gear and barring gear?
both are same utilizing for rotating the turbine initially


What's the distinction between crushing and grinding?
The means of human civilization is the process of refining,in this way grinding gear is the promotion of crushing equipment,however now we are able to discovered many cell crushing tools ,if youwant to know more particulars,please search domemachinery or bethcrushing on search engine.


What's the distinction between twerking and crumping?
Twerking is when a girl is grinding on a man, the man stops moving and the woman rubs all over his crotch while krumping often entails physical contact between dancers.


Your oranges should not turning orange on your tree?
That is both due to your number of orange , or there just isn't a big enough distinction within the temperature between day and night time. It is this distinction that promotes color change.


What is the grinding noise when turning left on front left tire?
Seems like you will have a bad left inner wheel bearing.


What would trigger a grinding or rattling sound when accelerating from a stop or when turning?
if its a entrance wheel drive vehicle then it could possibly be the axels


Why would a 2005 Mazda Protege make a excessive pitched grinding noise from the entrance proper while turning left and driving straight that stops if brakes are applied or when turning proper?
Are the breaks worn or have they been not too long ago replaced and could need new rotor. examine your wheel bearing as effectively. turning left puts extra stress on the precise side of the car, this could trigger the grinding noise.


What's the difference between fabricate and rebuilt gadgets on Crew Fortress 2?
fabricate is turning scrap into an merchandise, rebuild is turning objects into another item (rebuild 2 hats into 1 hat)


diamond blade
How does grinding pace up dissolving?
By grinding the surface space of the pattern increase and the contact between the solvent and solute is improved.

What is the distinction between the form from the solid type ice and the liquid kind?

Your answer

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Welcome to Newpost Q&A, where you can ask questions and receive answers from other members of the community.
...